background image

 

7

 

D - 

Installation and Warnings – Continued 

 

Gas Connection 

Make sure that the appliance is adjusted for the gas type available in your area (see the label under the 
appliance). Follow the instructions indicated in the chapter “gas transformations and adjustments” for the 
possible adaptation to different gases.  
The appliance must be connected to the gas system by means of still metal pipes or flexible steel pipes 
having continuous walls, in compliance with the regulations in force in your area. Some models are 
equipped with cylindrical A and conical B connectors for gas supply (fig. 7).  
 

 

WARNING: 

The connection must not stress the gas clamp.

 

 
Electric connection 

The connection to the electricity supply must be carried out by qualified personnel and in conformity with 
the regulations in force in your area.  
The voltage of the electric system must correspond to the value indicated in the label under the appliance. 
Make sure that the electric system is provided with an effective ground connection in compliance with the 
regulations and provisions of the law.  
 
Grounding is compulsory. 

 
GAS TRANSFORMATIONS AND ADJUSTMENTS 
Replacing the nozzles 

If the equipment is adjusted for a type of gas that is different from the original, it is necessary to replace the 
burner nozzles as well. The nozzles used to replace the original must be in accordance with the table of 
the technical characteristics enclosed. 
To remove the racks and burners by means of a straight spanner ‘L’, unscrew the nozzle ‘U’  
(Fig. 8) and substitute it with the corresponding one and tighten the nozzle. 

 
Adjusting the burners 

The flame should always stay alight when the burner is switched on, even if there is an abrupt shift from 
the maximum to minimum flame position. If the flame does not stay alight, adjust it as follows

 

Start the burner 

 

Turn the tap up to the minimum position (small flame) 

 

Remove the knob from the tap rod 

 

Using a flat-tip screwdriver ‘C’ into the hole ‘F’ of the tap (fig.9) turn the by-pass screw up. 

 
MAINTENANCE 
Lubricating the taps 

In the case of tap hardening, it is necessary to disassemble the tap and grease it. 

 

Unscrew the two screws that lock the head flange of the tap. 

 

Lift the gas adjusting cone and carefully clean it with gasoline or diluent. 

 

Spread a little high-temperature grease on it, making sure that the gas holes are not obstructed. 

 

Reassemble all of the parts with care. 

 

Replacing the power supply cable 

If the power supply cable needs to be replaced, it is necessary to use a cable with a section of 3 x 
0.75mm2, type H05VV-F or H05RR-F, complying with the regulations in force. 

 

NOTE: 

The connection to the terminal board must be effected as shown in fig. 10 - 10A: 

Brown cable L (phase) 
Blue cable N (neutral) 
Green-yellow cable (ground) 

Summary of Contents for 75040GM-M













Reviews: