background image

21

TECHNICAL DATA ON THE DATA LABEL

4 BURNERS

LPG = 28 - 30 mbar
LPG = 37 mbar
NATURAL = 20 mbar

Tot. Nom. Gas Rate = 7.5 kW
Tot. Nom. LPG = 545 g/h

Voltage = 230 – 240 V ~
Frequency = 50/60 Hz

3 B 

1 NORMAL PLATE

LPG = 28 - 30 mbar
LPG = 37 mbar
NATURAL = 20 mbar

Tot. Nom. Gas Rate = 5.75 kW
Tot. Nom. LPG = 418 g/h

Voltage = 230 – 240 V ~
Frequency = 50/60 Hz
Pot. Nom. El. Rating = 1000 W

3 B 

1 RAPID PLATE

LPG = 28 - 30 mbar
LPG = 37 mbar
NATURAL = 20 mbar

Tot. Nom. Gas Rate = 5.75 kW
Tot. Nom. LPG = 418 g/h

Voltage = 230 – 240 V ~
Frequency = 50/60 Hz
Pot. Nom. El. Rating = 1500 W

4 BURNERS WITH UR

LPG = 28 - 30 mbar
LPG = 37 mbar
NATURAL = 20 mbar

Tot. Nom. Gas Rate = 7.85 kW
Tot. Nom. LPG = 571 g/h

Voltage = 230 – 240 V ~
Frequency = 50/60 Hz

3 BURNERS WITH UR+

1 NORMAL PLATE

LPG = 28 - 30 mbar
LPG = 37 mbar
NATURAL = 20 mbar

Tot. Nom. Gas Rate = 6.1 kW
Tot. Nom. LPG = 444 g/h

Voltage = 230 – 240 V ~
Frequency = 50/60 Hz
Pot. Nom. El. Rating = 1000 W

3 BURNERS WITH UR+ 

1 RAPID PLATE

LPG = 28 - 30 mbar
LPG = 37 mbar
NATURAL = 20 mbar

Tot. Nom. Gas Rate = 6.1 kW
Tot. Nom. LPG = 444 g/h

Voltage = 230 – 240 V ~
Frequency = 50/60 Hz
Pot. Nom. El. Rating = 1500 W

OTHER MARKETS

4 BURNERS

LPG = 37 mbar
NATURAL = 20 mbar

Tot. Nom. Gas Rate = 7.5 kW
Tot. Nom. LPG = 545 g/h

Voltage = 1.5 V DC

4 BURNERS WITH UR

LPG = 28 - 30 mbar
LPG = 37 mbar
NATURAL = 20 mbar

Tot. Nom. Gas Rate = 7.85 kW
Tot. Nom. LPG = 571 g/h

Voltage = 1.5 V DC

OTHER MARKETS WITH BATTERY

Summary of Contents for 25658G-M





























Reviews: