ADVANTEST R3765AG Operation Manual Download Page 86

Page: 86 / 446

R3765/67G Series Network Analyzer Operation Manual

5.1 Measurement of Transmission Characteristic (2 Trace Display)

5-2

The display on the screen is as follows.
The display contents of input port on upper left of the screen are different depending
on the model.

The display of each type is as follows. (Active channel : CH2)

TRN : TRANSMISSION

The display section of input port (Example S21 : CG type)

Figure 5-1 Auto-scale of the First Trace of Magnitude/Phase

Measurement (Overlap Display)

AG type

BG type

CG type

B/R

TRN

S21

Summary of Contents for R3765AG































































































































































































































































































































































































































































Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands

ADVANTEST R3765AG, Operation Manual

Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands