manualshive.com logo in svg

ADVANTEST R3765AG, Operation Manual

Share
Download
ADVANTEST R3765AG Operation Manual Download Page 355

R3765/67G Series Network Analyzer Operation Manual

10.8 Crosstalk

10-29

10.8.4 When R3765CG/67CG (OPT 11/OPT 13/OPT 14)

(1)

Crosstalk of TEST PORT 1 (When the measurement path is S12)

Testing procedure 

Setup the R3765CG/67CG as follows.

Figure 10-17 Crosstalk of TEST PORT 1 (When the measurement path is S12)

Setup the R3765CG/67CG.

MEAS

: S12

RBW

: 100Hz

Average : 16 times

Connect the short standard to TEST PORT 2.

Connect the load standard to TEST PORT 1.

Read the crosstalk value of TEST PORT 1 from the trace data.

<Check> :

Crosstalk of TEST PORT 1

OPT 11
300kHz to 40MHz : -90dB or less
40MHz to 2.6GHz : -100dB or less
2.6GHz to 3.8GHz : -90dB or less
3.8GHz to 5.0GHz : -80dB or less  (R3767CG only)
5.0GHz to 8.0GHz : -70dB or less  (R3767CG only)

OPT 13
300kHz to 40MHz : -85dB or less
40MHz to 3.8GHz : -90dB or less

1

TEST
PORT1

TEST
PORT2

TEST
PORT3

R3765CG/67CG
(OPT11/OPT13/OPT14)

SHORT s

tan

dard

s

tan

dard

LO

AD

TEST
PORT4

2

3

4

5

6

Summary of Contents for R3765AG































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands