manualshive.com logo in svg

Advantek Networks ADR-18CU, User Manual, Page: 34 / 55

Share
Download
Advantek Networks ADR-18CU User Manual Download Page 34

ADSL Full-Rated Router    30

Destination MAC

: When the bridge filtering is enabled, enter the D

estination MAC address

, select 

Block

 and click

 Add

. Then all incoming WAN and LAN Ethernet packets matched with this destination 

MAC address will be filtered out. If the 

Forward

 is selected, then the packets will be forwarded to the 

destination PC.

Type

: Enter the hexadecimal number for the Ethernet type field in Ethernet_II packets. For example, 

0800 is for IP protocol.

5.3.7 DNS Configuration

This 

DNS Configuration

 page allows the user to set the configuration of DNS proxy.  The 

Conexant firmware supports the DNS proxy function. For the DHCP requests from local PCs, the DHCP 
server will set the LAN port first. The DNS proxy on the ADSL router recorded the available DNS servers, 
and forward DNS query messages to one of DNS server.

DNS Proxy

: User can enable or disable DNS Proxy feature.  For the DHCP requests from local PCs, 

the DHCP server will set the user-configured preferred DNS server or alternate DNS server whichever is 
available as the DNS server. Then all DNS query messages will be directly sent to the DNS servers.

Auto Discovered DNS Servers Only

: The DNS proxy will store the DNS server IP addresses obtained 

from DHCP client or PPP into the table. And all DNS query messages will be sent to one of the 
dynamically obtained DNS servers.

User Configured DNS Servers Only

: The DNS proxy will use the user-configured  DNS server and 

Summary of Contents for ADR-18CU
























































Reviews:

No comments