Advantech SmartMotion ST355 User Manual Download

Page: 45 / 51

SmartMotion ST355

7.8

Technical Parameters of Power over Ethernet (PoE)

Standards IEEE 802.3at-2009 (PoE+) and IEEE 802.3af-2003 (PoE) are supported. Ca-

bling needed is Category 5, up to 12.5

Ω

. It is possible to use a passive PoE injector.

PoE PD: parameters for opposite PSE

Input voltage range

42.5 – 57 V

Power available

25.50 W

Maximum current

600 mA

Table 27: PoE PD: parameters for opposite PSE

PoE PSE parameters

Power supply needed

44 – 57 V, 65 W

Power available

2x 25.50 W (ETH0, ETH1)

Table 28: PoE PSE parameters

7.9

Other Technical Parameters

Parameter

Description

CPU power

2 DMIPS per MHz

Flash memory

256 MB

RAM

512 MB

M-RAM

128 kB

Table 29: Other technical parameters

Summary of Contents for SmartMotion ST355




















































Search results

Summary of Contents for SmartMotion ST355

Reviews:

Related manuals for SmartMotion ST355

Brands by name

Popular brands

Advantech SmartMotion ST355, User Manual

Search results

Summary of Contents for SmartMotion ST355

Reviews:

Related manuals for SmartMotion ST355

Brands by name

Popular brands