Advantech SmartFlex SR310 Page 38 User Manual Download | Manualshive

Page: 38 / 59

background image

SmartFlex SR310

5.9

Interfaces Description

Besides the basic version of SmartFlex router there are available versions with one of the

following interfaces:

•

SWITCH interface

•

RS232-RS485/422 interface

•

RS232-RS485-ETH interface

5.9.1

SWITCH interface

The three LAN ports of the SWITCH interface for SmartFlex routers (RJ45 connectors for

connecting Ethernet devices) act as a typical switch device. This means that the router reads
Ethernet frames (data packets on an Ethernet link) from any port on the SWITCH interface and
transmits them on other ports of the SWITCH interface. Each port can transmit frames inde-
pendently on the other ports. State indication is displayed separately on each connector. These
router versions comply with the standards and temperature ranges stated in Chap.

except

for having a lower maximum operating temperature, which is +70

◦

C.

Figure 40: Version with SWITCH board

State indication of the interface:

Description of indication

Green LED

On
Off

Selected 100 Mbps
Selected 10 Mbps

Yellow LED

On
Blinking
Off

The network cable is connected
Data transmission
The network cable is not connected

Table 18: State indication of the SWITCH interface

31

«
...
36
37
38
39
40
...
»

Summary of Contents for SmartFlex SR310




























































Reviews:

No comments

Related manuals for SmartFlex SR310

IES615-2D Series

Brand: 3onedata Pages: 3

Brand: 3One data Pages: 5

Brand: 3onedata Pages: 33

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

totalstorage 200

Brand: IBM Pages: 180

Brand: Zalip Pages: 77

EtherFast LNE100TX ver. 5

Brand: Linksys Pages: 42

Brand: UTStarcom Pages: 71

RP614 - Web Safe Router

Brand: NETGEAR Pages: 16

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 17

Brand: Xantech Pages: 6

8-Port 10/100Mbps Fast Ethernet Switch

Brand: Amer.com Pages: 14

Brand: ZyXEL Communications Pages: 2

Brand: 8e6 Technologies Pages: 94

Brand: Tenda Pages: 82

Brand: M-Audio Pages: 67

Brand: Belkin Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands