Advantech SmartFlex SR310 Page 37 User Manual Download

Page: 37 / 59

SmartFlex SR310

5.8.10

Reset

When the

PWR

LED starts flashing on the front panel, it is possible to restore the de-

fault configuration of the router by pressing the

RST

button on the rear panel. After pressing

this button the default configuration will be restored and the router will reboot (after which the
green LED will be on).

It is necessary to use a narrow screwdriver or any other small tool to press the

RST

button.

Figure 39: Router reset

Before resetting the router, it is recommended to back up the router configuration set-
tings (see

Configuration manual

) because resetting the router will return all configuration

settings to their default states.

It is important to distinguish between the router reset and reboot.

Action

Router behavior

Invoking events

Reboot

Turns off and then turns on the router

Disconnect

and

reconnect

the

power,
press the

Reboot

button in the web

configuration

Reset

Restores the default configuration and
reboots the router

Press the

RST

button

Table 17: Description of router reset and restart

Summary of Contents for SmartFlex SR310




























































Search results

Summary of Contents for SmartFlex SR310

Reviews:

Related manuals for SmartFlex SR310

Brands by name

Popular brands

Advantech SmartFlex SR310, User Manual

Search results

Summary of Contents for SmartFlex SR310

Reviews:

Related manuals for SmartFlex SR310

Brands by name

Popular brands