Advantech SKY-8232D User Manual Download Page 96

Page: 96 / 133

SKY-8232D Manual V02 20220411

Page 96

Figure 3-36: PCIe Card Cage Assembly: External power adapter

11. Install the middle bar and the top cover.

12. Reconnect primary power and power on the unit.

13. Enter the BIOS setup menu, launch the EFI shell and use the PCIe device display

command to validate that the newly installed board(s) has/have been properly
recognized.

14. Leave the BIOS and boot the OS.

3.3.5Disk Installation

3.3.5.1 2.5

” HDD/SSD Drives

Note!

You need:

- A PH1 screw driver
- A standard 2.5

” HDD/SSD

Locate the disk tray you want to install the disk.

Push the tray

’s button to open the tray handle.

Figure 3-37: Opening the Disk Tray

Grab the tray handle and pull it evenly towards you.

Summary of Contents for SKY-8232D
























































































































Search results

Summary of Contents for SKY-8232D

Reviews:

Related manuals for SKY-8232D

Brands by name

Popular brands

Advantech SKY-8232D, User Manual

Search results

Summary of Contents for SKY-8232D

Reviews:

Related manuals for SKY-8232D

Brands by name

Popular brands