manualshive.com logo in svg

Advantech SKY-8101, User Manual

Share
Download
Advantech SKY-8101 User Manual Download Page 87

 

____________________________________________________________________________________________________ 

SKY-8200 Manual V04 20180321   

Copyright 2016 Advantech Co. Ltd. All rights reserved.   

Page 85

 

3.2.4 Server Management Setup 

The Server Mgmt menu supports configuring BMC related features such as OS Watchdog 
Timer, etc. 
 

 

Figure 3-23: Server Management Setup 

Table 3-16: Server Management Setup 

Group 

Setup Item 

Access / 
Options 

Description 

None 

BMC Self Test Status 

Display only 
(Passed) 

BMC self test status indication 
during power on process 

OS Watchdog Timer 

Enable 
Disable 

If enabled, starts a BIOS timer 
which can only be shut off by 
Management Software after the 
OS loads. 
Helps determine that the OS 
successfully loaded or follows 
the OS Boot Watchdog Timer 

OS Wtd Timer 
Timeout 

5 minutes 
10 minutes 
15 minutes 
20 minutes 

Configure the length of the OS 
Boot Watchdog Timer. Not 
available if OS Boot Watchdog 
Timer is disabled. 

OS Wtd Timer Policy 

Do Nothing 
Reset 
Power Down 

Configure how the system 
should respond if the OS Boot 
Watchdog Timer expires. Not 
available if OS Boot Watchdog 
Timer is disabled.       

Summary of Contents for SKY-8101











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands