Advantech SKY-8101 User Manual Download Page 44

Page: 44 / 138

____________________________________________________________________________________________________

SKY-8101S Manual V04 20180321

Page 42

2.4.2.1 PCIe Card Details

The SKY-8101S supports four rear facing PCIe card slots.

R10

R12

R11

Figure 2-10: PCIe Card Slot Details

Table 2-9: PCIe Card Slot Details

Item Element

Description

Power per PCIe slot

PCIe Slot,
Right Side #1

Full height, full length card slot at
top right

Maximum 100W for total two
slots (default)

Maximum 300W for total two
slots with additional customized
power cables

R10

PCIe Slot,
Right Side #2

Full height, full length card slot at
bottom right

R11

PCIe Slot,
Left Side #1

Half height, Low Profile card slot at
top left

Maximum 25W

R12

PCIe Slot,
Left Side #2

Half height, Advantech PersCard
slot at bottom left

Maximum 15W

Summary of Contents for SKY-8101











































































































































Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands

Advantech SKY-8101, User Manual

Search results

Summary of Contents for SKY-8101

Reviews:

Brands by name

Popular brands