Advantech POC-615 Series User Manual Download Page 52

Page: 52 / 64

POC-615 User Manual

The POC-615 series terminals feature a PCM-8722 printed circuit board assembly.

All jumpers and DIP switches are located on the top side of the motherboard.

7.1

Jumper Settings

CN3

ME Manufacturing Mode

CN5

Clear CMOS

CN6

Clear ME (reserved, not installed)

CN8

System Reset (reserved, not installed)

CN13

LVDS Voltage

CN40

Power Button (reserved, internal test only)

PCN4

Power Debug (reserved)

SW1

Board Setup

SW2

Panel Setup

CN3

ME Manufacturing Mode

Description

ME manufacturing mode

Setting

Function

(1-2)

ME manufacturing mode

(Not connected)

Normal operation (default)

CN5

Clear CMOS

Description

Clear CMOS setup

Setting

Function

(1-2)

Clear CMOS setup

(Not connected)

Normal operation (default)

CN6 (Not Installed)

Clear ME

Description

Clear ME setup

Setting

Function

(1-2)

Clear ME setup

(Not connected)

Normal operation (default)

Summary of Contents for POC-615 Series

































































Search results

Summary of Contents for POC-615 Series

Reviews:

Related manuals for POC-615 Series

Brands by name

Popular brands

Advantech POC-615 Series, User Manual

Search results

Summary of Contents for POC-615 Series

Reviews:

Related manuals for POC-615 Series

Brands by name

Popular brands