manualshive.com logo in svg

Advantech POC-615 Series, User Manual

Share
Download
Advantech POC-615 Series User Manual Download Page 36

POC-615 User Manual

24

3.4

Proper Handing

Handle the POC terminal with care. The device is made of metal, glass, and plastic

and  contains  sensitive  electronic  components.  Because  the  POC-615  terminal  is

heavy, we recommend using both hands when carrying the device. We also recom

-

mend using both hands when installing, removing, or replacing a battery pack.

Warning!

Do not attempt to use the POC-615 terminal if it is damaged (for exam

-

ple, the case is cracked or broken) as this may cause injury.
N'essayez pas d'utiliser le système POC-615 s'il est endommagé (par

exemple, le boîtier est fissuré ou cassé) car cela pourrait provoquer des

blessures.

Caution!

1.

Setup and install the POC-615 terminal on a stable surface. 

2.

Do not push objects into the ventilation openings. 

1.

Configurez et installez le système POC-615 sur une surface de tra

-

vail stable.

2.

Ne poussez pas d'objets dans les ouvertures de ventilation.

Summary of Contents for POC-615 Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands