Advantech IPPC-7157 Series User Manual Download Page 12

Page: 12 / 84

IPPC-7157 User Manual

• Keyboard/Mouse:

2 x PS/2 for mouse & keyboard interface

• LAN:

10/100/1000Base-T

• Memory:

4 x 240-pin Dual ch DDR2 DIMM sockets

(Up to 4 GB, Clock 266)

• Parallel Port:

1 x enhanced parallel port
Supports SPP/EPP/ECP parallel mode.
BIOS configurable to LPT1, LPT2, LPT3 or disabled

• Serial Ports:

1 x RS-232/422/485 on pin header

1 x RS-232 on rear I/O

• USB Ports:

1 x USB 2.0 on front panel

4 x USB 2.0 on rear I/O

1.2.3 LCD Display

• Backlight Life:

50,000 hrs

• Contrast Ratio:

500 : 1

• Display Size:

15"

• Display Type:

XGA TFT LCD

• Luminance:

250 cd/m2

• Max. Colors:

16.2 M (RGB 6-bit + FRC data)

• Max. Resolution:

1024x768

• OSD Control:

ON/OFF, Brightness down, up (behind the front panel)

• Viewing Angle (H/V°):

140/120

1.2.4 Touchscreen (Optional)

• Interface:

USB

• Lifespan:

10 million with silicone rubber of R8 finger, writing rate is 250g at 2X/s

• Light Transmission:

> 80% (AMT)

• OS Support:

Windows 95/98/ME/2000/XP/CE/NT/Vista, Linux

• Type:

8W Resistive

Summary of Contents for IPPC-7157 Series





















































































Search results

Summary of Contents for IPPC-7157 Series

Reviews:

Related manuals for IPPC-7157 Series

Brands by name

Popular brands

Advantech IPPC-7157 Series, User Manual

Search results

Summary of Contents for IPPC-7157 Series

Reviews:

Related manuals for IPPC-7157 Series

Brands by name

Popular brands