Advantech FWA-3050 User Manual Download Page 67

Page: 67 / 72

User Manual FWA-3050

_ v0.2 20200207.docx

2017

Page 67

5.2.5

Setup POST & Boot Menu

Users can configure the system boot priority settings via the boot page. The default setting of boot priority
of boot option #1 is “UEFI: Built-in EFI Shell”; Users can define the boot priorities based on the application.

Figure 400 Boot Configuration

Table 277 Boot Configuration

Feature

Default

Description

Setup Prompt Timeout

Number of seconds to

wait for setup

activation

key.

Bootup NumLock State

Select the keyboard NumLock state.

Quiet Boot

Disabled

Enables or disables Quiet Boot option.

Network Stack

Disabled

Enables or disables boot via Network (PXE)

Boot Option Priority

User Defined

Sets the system boot order.

CSM16 Parameters

Option ROM

Messages

Force BIOS

Keep Current

CSM Parameters

CSM Support

Enable the CSM support

Summary of Contents for FWA-3050


































































Search results

Summary of Contents for FWA-3050

Reviews:

Related manuals for FWA-3050

Brands by name

Popular brands

Advantech FWA-3050, User Manual

Search results

Summary of Contents for FWA-3050

Reviews:

Related manuals for FWA-3050

Brands by name

Popular brands