Advantech EKI-8500 Series User Manual Download Page 27

Page: 27 / 98

EKI-8500 Series User Manual

Make sure the module is seated correctly before sliding the module into the slot.

A click sounds when it is locked in place.

Figure 2.8 Installing an SFP Transceiver

Remove the protective plug from the SFP transceiver.

Insert the fiber cable into the transceiver. The connector snaps into place and

locks.

Figure 2.9 Attaching a Fiber Optic Cable to a Transceiver

Repeat the previous procedures to install any additional SFP transceivers in the

switch.

The fiber port is now setup.

2.4.2

Removing SFP Modules

To disconnect an LC connector, use the following guidelines:

Press down and hold the locking clips on the upper side of the optic cable.

Note!

If you are attaching fiber optic cables to the transceiver, continue with

the following step. Otherwise, repeat the previous steps to install the

remaining SFP transceivers in the device.

Note!

Do not remove the dust plug from the transceiver if you are not installing

the fiber optic cable at this time. The dust plug protects hardware from

dust contamination.

Handle

Summary of Contents for EKI-8500 Series



































































































Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands

Advantech EKI-8500 Series, User Manual

Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands