manualshive.com logo in svg

Advantech EKI-1526/N/I/TI, User Manual

Share
Download
Advantech EKI-1526/N/I/TI User Manual Download Page 87

73

EKI-1526(TI) | 1528(TI) User Manual

 

6.7.2

Event

In this page, you can configure events which will trigger logging or notification. You

can select three methods (Mail, SNMP, or log file) to record or send event messages.

System event notification is available for cold start, warm start, authentication failure,

IP address/Password change, serial DCD/DSR port change and Ethernet link down

information.

Trap Server

Use this field to indicate the IP address to use for receiving SNMP 

traps.

Trap Server Port

Enter the SNMP Trap server port.

Trap Version

(default = v1): Use this field to select the SNMP trap version.

Trap Community

Use this field to designate the SNMP trap community.

SNMP Agent Setting
Read Community

Read community name of your agent.

Write Community

Write community name of your agent.

Contact

Identify the system contact of your agent.

Location

Identify the system location of your agent.

Save

Click 

Save

 to save the values and update the screen.

Item

Description

Summary of Contents for EKI-1526/N/I/TI












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands