manualshive.com logo in svg

Advantech EKI-1526/N/I/TI, User Manual

Share
Download
Advantech EKI-1526/N/I/TI User Manual Download Page 53

39

EKI-1526(TI) | 1528(TI) User Manual

 

3.5.2.2

Unlock the Serial Device Server

To unlock the serial device server:

1.

Right-click a desired device to display the settings menu.

2.

Select 

Unlock Device

.

Figure 3.19 Unlock the Serial Device Server

3.

Enter the password as entered in the Lock Device procedure.
If  you  forgot  the  password,  you  must  restore  the  setting  of  the  serial  device

server to the factory defaults, which will be introduced in the next section.

3.5.3

Restore to Factory Default Settings

The configuration utility provides the function to restore the serial device server to

factory default settings. The confirm message will display after clicking 

Restore to

Factory Default Settings

. If you really want to restore the serial device server to

factory default settings, please click “Yes” button to continue.
Power off the serial device server within ten seconds. After reconnecting the power,

all settings will be reset to the factory default. If the power supply remains connected

for more than ten seconds, the serial device server will not be changed.

Summary of Contents for EKI-1526/N/I/TI












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands