manualshive.com logo in svg

Advantech EKI-1526/N/I/TI, User Manual

Share
Download
Advantech EKI-1526/N/I/TI User Manual Download Page 38

EKI-1526(TI) | 1528(TI) User Manual

24

3.1

Configuration Utility Overview

Advantech EKI series serial device servers provide an easy-to-use utility to configure

your  serial  device  server  through  an  Ethernet  connection.  After  the  installation

program on the Advantech EKI Device Configuration Utility CD-ROM is finished, the

serial device servers are ready for use and configuration.
Advantech  Serial  Device  Server  Configuration  Utility  is  an  excellent  device  server

management tool. You can connect and configure the local and remote Advantech

serial device servers easily. The utility provides access to the following functions:

Configure the network settings (you can set the IP address, Gateway address, 

and Subnet mask)

View the serial port parameters

Perform diagnostic tests (virtual COM port testing, port status list)

Upgrade firmware

3.2

Installing the Configuration Utility

1.

Insert the Advantech EKI Device Configuration Utility CD-ROM into the CD-

ROM drive on the host PC.

2.

Use Windows explorer or the Windows Run command to execute the setup 

program; the name of the setup program on the CD-ROM is "EKI Device 

Configuration Utility".

3.

If there is an existing COM port mapping utility on the host PC, remove it at this 

time. A system reboot may be necessary before continuing the installation.

4.

Once the InstallShield Wizard screen displays, click 

Next

 to proceed with the 

installation.

Figure 3.1 InstallShield Wizard 1 of 4

Note!

Microsoft .NET Framework version 2.0 or greater is required for this 
application.

Summary of Contents for EKI-1526/N/I/TI












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands