manualshive.com logo in svg

Advantech BB-VESR90 Series, User Manual, Page: 35 / 53

Share
Download
Advantech BB-VESR90 Series User Manual Download Page 35

 

BB-VESR90x Serial Servers

 

 

30 

 

VCOM (VIRTUAL COM PORT) 
When the Network Protocol is set to 

VCOM (Virtual COM Port), 

the 

serial server communicates over the network with a PC, acting as a 

remote COM port for the computer.  
Both the serial server and the computer must be configured for VCOM 

operation. Virtual COM ports can be set up on the PC using the Vlinx 

Manager software. 

 

UPGRADING SERIAL SERVER FIRMWARE 

Occasionally, updated firmware may become available for your serial 

server. The firmware can be upgraded using the Vlinx Manager software. 

The following procedure describes the firmware updating process:  

1.  Click 

Upgrade

 button to open 

Firmware Upgrade 

dialog box.  

 

Firmware Upgrade Dialog Box 

The name of the currently selected serial server appears in the top

 

drop 

down list. Other serial servers (that have already been discovered) can 

be selected from the drop down list, if desired. 

 

The current firmware version of the selected serial server is shown in the 

text below the serial server name. 

 

Information about the selected firmware file is shown in the third text box. 

 

 

Summary of Contents for BB-VESR90 Series






















































Reviews:

No comments