manualshive.com logo in svg

Advantech Wireless AWMA-Kx500-BTE Series, Installation And Operating Manual

Share
Download
Advantech Wireless AWMA-Kx500-BTE Series Installation And Operating Manual Download Page 25

 

 

 

 

AWMA-Kx500-BTE

 
 
 
 

TABLE 6

: RELAY INTERFACE – PIN ASSIGNMENT 

Pin

  Signal Name 

Description

 

A Tx 

AL-NC 

Normal closed contact of the 

Tx ALARM

 Form - C relay. 

Pin A closed to pin B indicates ALARM in the transmission path. 

B Tx 

AL-COM 

Common contact of the 

Tx ALARM

 Form - C relay 

C Tx 

AL-NO 

Normal open contact of the 

Tx ALARM

 Form – C relay. 

Pin C open relative to pin B indicates ALARM in the transmission 
path. 

D N/C 

Not 

connected 

E N/C 

Not 

connected 

F N/C 

Not 

connected 

G Tx 

MUTE 

Tx MUTE command

: 

If pin G is NOT connected to pin H, the transmission path is MUTE. 
If pin G is connected to pin H, the transmission path is ON. 

H MUTE-COM 

Common contact of the 

Tx MUTE and Rx MUTE Commands

 

J N/C 

Not 

connected 

K OUT-MON 

Output Power Monitor (voltage: 5 V DC at rated P1dB; > 0 V DC at 
20 dB back-off) 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

24

 

Summary of Contents for AWMA-Kx500-BTE Series




















































Reviews:

No comments

Brands by name

Popular brands

Load more brands