Advantech-DLoG DLT-V83 Series Operating Instructions Manual Download Page 71

Page: 71 / 157

General device configuration

DLT-V83 Operating Instructions V2.00

71 / 157

10.7.1.

iManager

The "iManager" offers embedded firmware that can be used to manage and test the onboard devices

simply and independently from the operating system. This improves system stability and compatibility.

The "iManager" offers a collection of standardized APIs for hardware monitoring, GPIO

selection/analysis, Multi-Level-Watchdog and more.

In the area

GPIO Bank Control

, outputs DO1 to DO3 can be set and inputs DI1 and DI2 can be

queried:

Fig. 10.3: iManager: GPIO Bank Control

Information about the "iManager" is available in the Internet at

http://www.advantech.de/embcore/imanager.aspx

Hardware details such as the pin assignment of the CAN and Digital I/O interfaces are described in the

following chapter:

7.3.4 CAN, digital I/O and second Ethernet interface (optional)

Summary of Contents for DLT-V83 Series






























































































































































Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands

Advantech-DLoG DLT-V83 Series, Operating Instructions Manual

Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands