Advantech-DLoG DLT-V83 Series Operating Instructions Manual Download Page 68

Page: 68 / 157

General device configuration

68 / 157

DLT-V83 Operating Instructions V2.00

10.5.

Configuring the front keys, automatic shutdown, etc.

Use the “DLoG Config Tool” for settings like the following:

−

Configure the front keys of the DLT-V83.

−

Configure the WLAN status display.

−

Define the switching on and off of the DLT-V83 in conjunction with the vehicle ignition (automatic

shutdown).

For configuring DLT-V83, the DLoG Config version 4.0.3 (or higher) is required.

The DLoG Config manual is available on our websites.

Fig. 10.1: DLoG Config Tool main menu, example Win 10 IoT Enterprise

Summary of Contents for DLT-V83 Series






























































































































































Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands

Advantech-DLoG DLT-V83 Series, Operating Instructions Manual

Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands