Advantech-DLoG DLT-V83 Series Operating Instructions Manual Download Page 50

Page: 50 / 157

Open/close antenna (or protective cap)

50 / 157

DLT-V83 Operating Instructions V2.00

8.3.2.

WLAN antenna IEEE 802.11 a/b/g/n/ac

Open antenna:

Fig. 8.2: Open WLAN antenna IEEE 802.11 a/b/g/n/ac



Unfasten both screws on the

antenna. Tool: Allen key (size 3)



Remove the antenna from the device.

Fig. 8.3: WLAN antenna IEEE 802.11 a/b/g/n/ac opened

Service USB, CFast and mini SIM card
slot are now accessible.

For details, see section

7.5.1 Information

on service USB, CFast and

Mini SIM card

slot.

Close antenna:



Place the antenna back onto the DLT-V83.



Tighten both screws (1 Nm torque).

Summary of Contents for DLT-V83 Series






























































































































































Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands

Advantech-DLoG DLT-V83 Series, Operating Instructions Manual

Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands