Advantech-DLoG DLT-V83 Series Operating Instructions Manual Download Page 35

Page: 35 / 157

Technical data on radio modules

DLT-V83 Operating Instructions V2.00

35 / 157

6.3.6.

External WWAN antenna 3G

Fig. 6.6: External 3G WWAN antenna (optional)

Technical data

Application

WWAN 3G technology

Mounting location

For detached mounting, e.g. on the roof of the forklift

WWAN frequency range

Transmitting

(TX)

AMPS: 824 to 849 MHz

GSM 900: 880 to 915 MHz

GSM 1800: 1710 to 1785 MHz

GSM 1900: 1850 to 1910 MHz

UMTS: 1900 to 2025 MHz

WWAN frequency range

Receiving (RX)

AMPS: 869 to 894 MHz

GSM 900: 925 to 960 MHz

GSM 1800: 1805 to 1880 MHz

GSM 1900: 1930 to 1990 MHz

UMTS: 2110 to 2170 MHz

Number of antennas

Type

Omnidirectional antenna

Antenna gain

Typically 0 dBi (5.1 dBi)

Impedance

50 Ω

Polarization

Vertical/horizontal

Dimensions

33 mm x 89 mm

Maximum transmitting power

250 mW / 24 dBm

Compatible WWAN card

USA: SIERRA WIRELESS MC8090

Europe: SIERRA WIRELESS MC8092

(see section

6.2.2 Available

Radio cards)

Summary of Contents for DLT-V83 Series






























































































































































Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands

Advantech-DLoG DLT-V83 Series, Operating Instructions Manual

Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands