manualshive.com logo in svg

Advanjet HV-2100 Jet, Setup And Operation

Share
Download
Advanjet HV-2100 Jet Setup And Operation Download Page 9

2.3 

Cable Connections 

The cable connections for a typical dispensing system are illustrated below. To assure 
proper connections, each of the component cables supplied by Advanjet has a distinct 
connector. Be sure that all power is off when connecting and disconnecting any cable to 
the Advanjet controller. 

 

Jet:

 A 28-pin cable (P/N 06-1095-00) mates with the HV-2100 jet cable to connect it to 

the HV-2100C controller. Section 2.4 provides HV-2100 Jet Cable pin assignments.  

I/O:

  When using the HV-2100 jet with the HV-2100C controller and a robot, six  TTL 

trigger lines control jet operations through a 26-pin cable (P/N CB26-005).  

COMM:

  A PC can be connected to the controller  via  RS-232C/USB  to operate the 

HV-2100 using software instead of the front panel touch screen.  

 

 

Figure 2-3: Cable Connections for the HV-2100 in a Typical Dispensing System 

3A6244A 

Advanjet HV-2100 Jet Setup and Operation 

Page 9 of 22 

Summary of Contents for HV-2100 Jet























Reviews:

No comments

Brands by name

Popular brands

Load more brands