Advanjet HV-2100 Jet Setup And Operation Download Page 22

 

Graco Standard Warranty 

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from 
defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, 
extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace 
any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, 
operated and maintained in accordance with Graco’s written recommendations. 

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused 
by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or 
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility 
of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, 
manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. 

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for 
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The 
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any 
defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, 
and transportation. 

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT 
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE

.  

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no 
other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or 
property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within 
two (2) years of the date of sale. 

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 
A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD 
BUT NOT MANUFACTURED BY GRACO

. These items sold, but not manufactured by Graco (such as electric motors, switches, 

hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in 
making any claim for breach of these warranties. 

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment 
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, 
breach of warranty, the negligence of Graco, or otherwise. 

FOR GRACO CANADA CUSTOMERS 

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal 
proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les 
parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et 
procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures 
concernées. 

 

Graco Information 

For the latest information about Advanjet products, visi

www.advanjet.com. 

For patent information, see 

www.graco.com/patents. 

For customer service and technical assistance, e-mail 

[email protected]

 

 

TO PLACE AN ORDER, contac

[email protected]

 

 

If calling from the US: 800-333-4877 

 

If calling from outside the US: +1-760-294-3392 

 
 

All written and visual data contained in this document reflects the latest product information available at the time of publication.  

Graco reserves the right to make changes at any time without notice. 

Original instructions.

 This manual contains English. MM 3A6244 

Graco Headquarters: 

Minneapolis 

International Offices: 

Belgium, China, Japan, Korea 

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA 

Copyright 2019, Graco Inc. All Graco manufacturing locations are registered to ISO 9001. 

www.graco.com 

Revision A, April 2019 

Summary of Contents for HV-2100 Jet























Reviews: