Advanced HBC-3130 User Manual Download Page 7

K. Trouble Shooting

PROBLEM

INDICATIONS

POSSIBLE CAUSES

SUGGESTED SOLUTION

Charger does not
work 

Indicator lights not
turn on 

No AC power

AC input socket fuse blown 

Check AC connections are correct 

Replace with correct AC fuse by qualified
electrician

No DC output 

Charger - On LED is
not on, Float and
Fault LEDs are on

Output short circuit 

Over temperature protection triggered 

Severe over loading charger

Reverse polarity connection

DC fan locked by foreign object or
malfunction

Check DC connections between charger
and battery. Charger can auto reset if
remove the fault within 20 seconds.

Check air intake vent at bottom of charger
is blocked or not. Check charger ambient
ventilation .

Check battery AH capacity within
recommended range

Check for correct polarity, replace car
blade fuse (6)

Check DC fan

Battery does not get
full charge

All indicator LED
work normally and
sequentially 

OTP LED flashing

Bad battery connection 

Battery type select switch in wrong setting

Battery capacity too large

Ambient temperature too low 

Battery has damaged cell or battery is too
old 

Wrong set the lower power level

Check for loose contact, right cable size,
cable integrity

Recheck battery type and change to
correct battery selection

Make sure charger rating matches battery
capacity see table

 

(B2)

Move battery to a room temperature
location, or get an optional temperature
sensor 

Replace battery

Recheck the current selection switch (5) to
correct right setting

Long charging
time , float light
does not come on
even after 12 hours
charging time.

Absorption light
remains on all the
time 

Charger internal fault 

Return the charger to distributor to repair 

Bulk LED is on all
the time 

Bulk light remains
on all the time 

Wrong battery type selection

Battery is excessively depleted and the
soft charging is triggered  

Battery temperature too high

Check charged battery label and change
battery type selection to correct setting

Recharge the battery after a day, if bulk
light remains after several hours, the
battery is most likely damaged and cannot
accept charge. Replace battery.

Use accessory temperature sensor

Summary of Contents for HBC-3130























Reviews: