Quick Start Guide, 61200890L1-13D, July 2005
Technical Support 1-888-4ADTRAN (1-888-423-8726)
Copyright © 2005 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at
www.adtran.com
.
Quick Start Guide
®
NetVanta 4305 Router
P/N 1200890L2
STATUS
NET 2
WAN
DBU
TD
RD
TD
RD
LNK
LAN 2
NetVanta 4305
STATUS
ACTIVITY
TEST
WIDE SLOT 1
TD
RD
LNK
LAN 1
NET 1
WAN
DBU
TD
RD
G
ETTING
S
TARTED
Two configuration methods are available for your NetVanta router:
•
Web-based GUI
•
AOS Command Line Interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and explanations
for each setting. However, using the AOS CLI may be necessary for more advanced
configurations.
A
CCESS
THE
GUI
You may access the web-based GUI from any web browser on your network by following these
steps:
1.
Connect the router to your PC using the
ETH 0/1
port on the back of the unit.
2.
Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address,
you will need to change the unit’s IP address using the CLI. (Refer to the next two sections for
instructions.)
3.
Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1.
4.
You will then be prompted for the username and password (the default settings are
admin
and
password
).
5.
The initial GUI screen appears.
A
CCESS
THE
CLI
Access the AOS CLI via the
CONSOLE
port or a Telnet session. To establish a connection to the
NetVanta router
CONSOLE
port, you need the following items:
•
VT100 terminal or PC (with VT100 terminal emulation software)
•
Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end
1.
Connect the DB-9 (male) connector of your serial cable to the
CONSOLE
port on the rear
panel of the unit.
2.
Connect the other end of the serial cable to the terminal or PC.
3.
Insert the connector of the provided power cord into the power interface on the rear panel of
the unit, and plug the cord into a standard electrical outlet.
4.
Once the unit is powered up, open a VT100 terminal session using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press
<Enter>
to activate the
AOS CLI.
5.
Enter
enable
at the
>
prompt.
6.
Enter the enable password when prompted. The default password is
password
.
C
ONFIGURE
THE
U
NIT
’
S
IP A
DDRESS
The following steps create an IP address (10.10.10.1 255.255.255.0) for Ethernet port 0/1. If you
are not sure what IP address to assign, please contact your network administrator.
1.
At the
#
prompt, enter
config terminal
.
2.
At the
(config)#
prompt, enter
interface eth 0/1
to access the configuration parameters for
the
ETH 0/1
port located on the rear of the unit.
3.
Enter
ip address 10.10.10.1 255.255.255.0
to assign an IP address to the
ETH 0/1
port using
a 24-bit subnet mask.
4.
Enter
no shutdown
to activate the interface to pass data.
5.
Enter
exit
to exit the Ethernet interface commands and return to the Global Configuration
mode.
The configuration parameters used in the examples outlined in this
document are for instructional purposes only. Please replace all
underlined entries (
example
) with your specific parameters to configure
your application.
Depending on your configuration, you may need to set a default gateway
as well using the
(config)#ip default gateway
command. If IP routing is
enabled on the unit, do NOT set a default gateway.
