Quick Start Guide, 61200506L1-13A, March 2006
Technical Support 1-888-4ADTRAN (1-888-423-8726)
Copyright © 2006 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at
www.adtran.com
.
Quick Start Guide
®
NetVanta 1024 PWR Power over Ethernet Midspan
P/N 1200506L1
DATA & POWER
DATA
NetVanta 1024
Power over Ethernet
P
OWER
OVER
E
THERNET
The NetVanta 1024 PWR Power over Ethernet Midspan products provide a cost effective way to
offer power over Gigabit Ethernet to existing nonpowered switches. These units deliver 15.4 watts
per port (up to 370 watts), supporting power over Ethernet. This supplies 48 VDC to powered
devices (e.g., IP phones, wireless access points, IP cameras, etc.) over existing CAT5 cabling.
These NetVanta products are fully compliant with IEEE 802.3af Power over Ethernet (PoE)
standards, and they support legacy (pre-standard) PoE.
By default, the midspan products detect and provide power to nonpowered switches.
G
ETTING
S
TARTED
Two configuration methods are available for your NetVanta unit:
•
Web-based GUI
•
AOS Command Line Interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and explanations for
each setting. However, using the AOS CLI may be necessary for more advanced configurations.
A
CCESS
THE
GUI
You can access the web-based GUI from any web browser on your network by following these
steps:
1.
Connect the unit to your PC using the
ETH 0/0
port on the rear of the unit.
2.
Set your PC to a fixed IP address of
10.10.10.2
. If you cannot change the PC’s IP address, you
will need to change the unit’s IP address using the CLI. (Refer to the next two sections for
instructions.)
3.
Enter the unit’s IP address in your browser address line. The default IP address is
10.10.10.1
.
4.
You will then be prompted for the username and password (the default settings are
admin
and
password
).
5.
The initial GUI screen appears.
A
CCESS
THE
CLI
Access the AOS CLI via the
CONSOLE
port or a Telnet session. To establish a connection to the
NetVanta unit
CONSOLE
port, you need the following items:
•
VT100 terminal or PC (with VT100 terminal emulation software)
•
Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end
1.
Connect the DB-9 (male) connector of your serial cable to the
CONSOLE
port on the rear
panel of the unit.
2.
Connect the other end of the serial cable to the terminal or PC.
3.
Insert the connector of the provided power cord into the power interface on the rear panel of
the unit, and plug the cord into a standard electrical outlet.
4.
Once the unit is powered up, open a VT100 terminal session using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press
<Enter>
to activate the AOS CLI.
5.
Enter
enable
at the
>
prompt.
6.
Enter the enable password when prompted. The default password is
password
.
C
ONFIGURE
THE
U
NIT
’
S
IP A
DDRESS
The following steps create an IP address and subnet mask for the
ETH 0/0
port. If you are not sure
what IP address to assign, please contact your network administrator.
1.
At the
#
prompt, enter
config terminal
.
2.
At the
(config)#
prompt, enter
interface eth 0/0
to access the configuration parameters for
the Ethernet interface.
3.
Enter
ip address 10.26.12.12 255.255.255.0
to assign an IP address to the Ethernet
interface using a 24-bit subnet mask.
4.
Enter
no shutdown
to activate the interface to pass data.
5.
Enter
exit
to return to the Global Configuration mode.
Depending on your configuration, you may need to set a default gateway
as well using the
(config)#ip default gateway
command. If IP routing is
enabled on the unit, do NOT set a default gateway.
