job
Aid
1
D
ESCRIPTION
The 10G DWDM Tunable XFP is a fully duplex serial electric,
serial optic device with both transmit and receive functions
contained in a single module that provides a high speed serial
link at 10 Gbs. The Tunable XFP is controlled by software on the
host module and can operate on the full C-band supporting
Channels 17 through 60. Installed in the appropriate host module,
the Tunable XFP provides a 10 Gigabit interface to the supporting
system. Refer the documentation provided with the host module
for information on configuring the XFP.
The transmit side of the Tunable XFP converts serial NRZ
electrical data at the 10 Gbs line rate to a standard compliant
optical signal. The receive side converts the incoming DC
balanced serial NRZ optical data at the 10 Gbs line rate into serial
electrical data.
NOTE
To ensure compatibility, refer to the documentation provided
with the host module.
The following features are supported on the Tunable XFP:
•
1529.55 ~ 1563.86 nm optical signals for up to 80 km reach
•
Low power consumption (<3.5 W max)
•
Bit error rate 10^–12
CAUTION
!
Due to compliance certification requirements, use only XFPs
supplied by ADTRAN with the host module. ADTRAN cannot
certify system integrity with other XFPs.
Small Form-Factor Pluggable
10G DWDM Tunable XFP
O
PERATIONAL
S
PECIFICATIONS
•
Transmit Wavelength: Tunable 1529.55 ~ 1563.86 nm
(Channels 17 through 60)
•
Receive Wavelength: 1528.77 to 1600 nm
•
Data Rate: 9.95 Gbs to 11.35 Gbs (see table below)
•
Optical transmit levels: –1.0 to +3.0 dBm
•
Optical receive level: –24.0 to –7.0 dBm
•
Dispersion Tolerance: -400ps/nm to 1600ps/nm
•
Dispersion penalty maximum: 2.5dB (-400 to 1600ps/nm)
•
Minimum Span Attenuation: 10 dB
•
Optical distance: 80 km maximum
•
Optical connectors: LC
•
Extended Environmental Support:
o
Operational temperature range: –5°C to +60°C
o
Storage temperature range: –40°C to +85°C
o
Relative humidity to 85%, noncondensing
I
NSTALLATION
Before installing the equipment, inspect the Tunable XFP. If
damage has occurred during shipping, file a claim with the
carrier, and then contact ADTRAN Customer Support. For more
information, refer to the warranty.
To install the Tunable XFP into an appropriate module, complete
the following steps:
NOTE
Do not remove the protective end cap from the XFP until the fiber
optic cable is ready to be connected.
1. Insert the Tunable XFP into the XFP cage on the module.
Ensuring that the latch handle on the XFP is facing upward,
slide the XFP all the way into the XFP cage until there is an
audible “click”.
NOTE
The latch on the XFP is for removal only. When removing the
XFP, rotate the latch away from the XFP, the XFP should easily
slide out of the cage.
2. Do not remove the protective end cap until the optical fiber
connection is made.
Without FEC
1
1. Forward Error Correction (FEC) at BER 1E-12, input power -7 to -19 dBm
With FEC
2
2. Forward Error Correction (FEC) at BER 1E-4, input power -7 to -24 dBm
Data Rate
BOL
EOL
BOL
EOL
9.95Gbps
>26 dB
>27 dB
NA
NA
Up to 10.7Gbps
NA
NA
>17.5 dB
>18.5 dB
Up to 11.1Gbps
NA
NA
>18.5 dB
>19.5 dB
Up to 11.35Gbps
NA
NA
>18.5 dB
>19.5 dB
CLEI: BVL3AP6D_ _
Product P/N: 1442985G1C
Issue Date: March 2012
Document P/N: 61442985G1C-22A
