ADTEK AEM-DRB Operation Manual Download Page 34 | Manualshive

Page: 34 / 44

ADTEK AEM-DRB Operation Manual Download Page 34

30

8. Press ENTER key on the menu page to enter alarm set setting
9. Press UP or DOWN key to select the alarm condition group.
10. Press ENTER key to enter alarm conditional setting.
11. Press ENTER key to enter alarm mode setting.
12. Press UP and DOWN key to select alarm mode.
13. Press ENTER key to finish setting and return to the previous menu.
14. Press ENTER key to select loop setting.
15. Press UP and DOWN key to select the loop.
16. Press ENTER key to finish setting and return to the previous menu.
17. Press ENTER key to enter object setting.
18. Press UP and DOWN key to select parameter.
19. Press ENTER key to finish setting and return to the previous menu.
20. Press ENTER key to enter set point setting.
21. Press UP or DOWN key to select the numeric.
22. Press LEFT key move to the next digit.
23. Repeat step 21 to 22 until finishing all digit setting of set point, press ENTER key to

save and return to the previous menu.

※ Press LEFT key and hold 2 seconds to cancel input and return to the previous menu.

4.1.12 Initial

• Recover the power meter to factory default value. The default password is 7170.
• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter initial setting.
2.  Press UP or DOWN key to select the numeric.
3.  Press LEFT key move to the next digit.
4.  Repeat step 2 to 3 until finishing 4-digit setting of password, press ENTER key confirm

initial and return to the previous menu.

※ Press LEFT key and hold 2 seconds to cancel input and return to the previous menu.
※ The meter will restart when initial starts operating.

«
...
32
33
34
35
36
...
»

Summary of Contents for AEM-DRB













































Reviews:

No comments