ADTEK AEM-DRB Operation Manual Download Page 31 | Manualshive

Page: 31 / 44

ADTEK AEM-DRB Operation Manual Download Page 31

27

4.1.9 Date/Time

4.1.9.1 Backlight Time

4.1.9.2 Date

4.1.9.3 Time

4.1.9.4 Operation Hour Reset

• LCM backlight time setting. The setting range is 0 ~ 15 minutes, 0 means the light stays

always on. The default value is 1.

• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter the backlight time setting.
2.  Press UP or DOWN key to select the numeric.
3.  Press LEFT key move to the next digit.
4.  Repeat step 2 to 3 until finishing 2-digit setting of time, press ENTER key to save and

return to the previous menu.

※ Press LEFT key and hold 2 seconds to cancel input and return to the previous menu.

• Date setting. The setting range is 2010/1/1 ~ 2099/12/31.
• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter the date setting.
2.  Press UP or DOWN key to select the numeric.
3.  Press LEFT key move to the next digit.
4.  Repeat step 2 to 3 until finishing 8-digits setting of date, press ENTER key to save and

return to the previous menu.

※ Press LEFT key and hold 2 seconds to cancel input and return to the previous menu.

• Time setting. The selectable range is 00: 00: 00 ~ 23: 59: 59.
• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter the time setting.
2.  Press UP or DOWN key to select the numeric.
3.  Press LEFT key move to the next digit.
4.  Repeat step 2 to 3 until finishing 6-digits setting of time, press ENTER key to save and

return to the previous menu.

※ Press LEFT key and hold 2 seconds to cancel input and return to the previous menu.

• Reset the operation hour.
• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter operation hour reset setting.
2.  Use UP and DOWN key to select “YES” for clear or “NO” for leave.
3.  Press ENTER key to finish setting and return to the previous menu..

※ Press LEFT key to cancel input and return to the previous menu.
※ The operation hour starts accumulating after the meter starts running.

«
...
29
30
31
32
33
...
»

Summary of Contents for AEM-DRB













































Reviews:

No comments