manualshive.com logo in svg

ADTEK AEM-DRB, Operation Manual, Page: 29 / 44

Share
Download
ADTEK AEM-DRB Operation Manual Download Page 29

25

4.1.6.5 Module Control

• The control function of the communication module can restart the communication module 

or restore the set related parameters to the factory default values.

• After the Ethernet parameters are changed, the module must be restarted to take effect.
• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter Force Reboot.
2.  Use UP and DOWN key to select Yes or No.
3.  Press ENTER key to finish setting and return to the previous menu.
4.  Press ENETER key to enter Set to Default setting.
5.  Use UP and DOWN key to select Yes or No.
6.  Press ENTER key to finish setting and return to the previous menu.

※  Press LEFT key to cancel the changes and return to the previous menu.

4.1.7 Pulse Output

4.1.7.1 Test Pulse

4.1.7.2 Target Loop

• Set the test pulse output function is enabled or disabled because the default value is 

disabled. The pulse output is fixed at 3200 Pulse / 1kWh, and the duty cycle is 50%.

• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter test pulse setting.
2.  Use UP and DOWN key to select enable or disable.
3.  Press ENTER key to finish setting and return to the previous menu.

※  Press LEFT key to cancel input and return to the previous menu.

• Select the loop corresponding to the pulse output. The default value is main loop A.
• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter target loop setting.
2.  Use UP and DOWN key to select the corresponding loop.
3.  Press ENTER key to finish setting and return to the previous menu.

※  Press LEFT key to cancel input and return to the previous menu.

Summary of Contents for AEM-DRB













































Reviews:

No comments