manualshive.com logo in svg

ADTEK AEM-DRB, Operation Manual, Page: 26 / 44

Share
Download
ADTEK AEM-DRB Operation Manual Download Page 26

22

6.  Press ENTER key to enter the CT secondary. This setting is only available for the main 

loop.

7.  Press UP or DOWN to select the ampere.
8.  Press ENTER key to finish setting and return to the previous menu.

※  Press LEFT key to cancel input and return to the previous menu.

4.1.5.4 Branch Loop Voltage Phase Assign

• The voltage phase of each branch loop can be specified according to the actual CT 

mounting conditions and measurement needs to obtain the required power measurement 
data.

• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter voltage assign setting.
2.  Press UP or DOWN key to select the loop to be set, press ENTER key to enter.
3.  Press UP or DOWN key to select the corresponding voltage phase of the loop.
4.  Press ENTER key to finish setting and return to the previous menu.

※  Press LEFT key to cancel input and return to the previous menu.

4.1.5.5 Modify Password

• Change user password, the default value is 1000.
• Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter password setting.
2.  Press UP or DOWN key to select the numeric.
3.  Press LEFT key move to the next digit.
4.  Repeat step 2 to 3 until finishing 4-digits, press ENTER key to save and return to the 

previous menu.

※  Press LEFT key and hold 2 seconds to cancel input and return to the previous menu.

4.1.5.6 Default Page

• Default Page：On the default page of the meter, optional Summary-1(VLLavg/Iavg/Psum/

Freq),  Summary-2(sum/Qsum/Ssum/PFavg),  Summary-3(VLLavg/Iavg/Psum/PFavg), 
Summary-4/5/6  and  Summary-1/2/3  are  the  same  parameter.  Summary  1-6  both  can 
select the corresponding circuit individually. Summary-P is a user-defined page, and 
the corresponding loop and parameter items can be set by yourself. In addition, all the 
default page can be set to display one by one.

•  Steps of setup are as follows:

1.  Press ENTER key on the menu page to enter default page setting.
2.  Press UP or DOWN key to select the page to be set.
3.  Press ENTER key to finish setting and return to the previous menu.
4.  Press ENTER key to enter specify loop setting.
5.  Press UP or DOWN key to select the default page to be set, press ENTER key to enter.

Summary of Contents for AEM-DRB













































Reviews:

No comments