Adtech ADTECH4 CNC Series Maintenance Manual Download Page 63

Page: 63 / 201

ADTECH4 SeriesCNC Maintenance Manual

Tool Compensation Parameter Setting Interface

9.8

M series workpiece coordinate system setting interface

The coordinates interface shows coordinate system info, including setting, coordinate system, centered,

and tool regulator. In the main interface, press [Coordinate] to enter coordinate system.

Workpiece coordinate system

Display workpiece coordinate system, i.e. the offset of workpiece home position and machine tool home

position, Totally six basic workpiece coordinate systems (G54~G59) and nine extension coordinate systems

(G591~G599) are available.

To enter workpiece coordinate system interface:

The workpiece coordinate system interface is shown below:

M series [coordinates]

[Coordinate

settings]

[Coordinates]

[Coordinate

settings]

Summary of Contents for ADTECH4 CNC Series










































































































































































































Search results

Summary of Contents for ADTECH4 CNC Series

Reviews:

Related manuals for ADTECH4 CNC Series

Brands by name

Popular brands

Adtech ADTECH4 CNC Series, Maintenance Manual

Search results

Summary of Contents for ADTECH4 CNC Series

Reviews:

Related manuals for ADTECH4 CNC Series

Brands by name

Popular brands