ADRF PSR-78-9533-UA Manual Download | Manualshive

Page: 38 / 60

background image

Advanced RF Technologies, Inc.

38

7.2.3

Alarms

This section displays the alarm status for System alarms, RF Alarms, and Power alarms. If an alarm is present
in the system, then the color of the alarm tab will change according to the type of failure.

Figure 7-2

Status Tab – Alarm Display

7.2.4

AAI

This section displays the AAI alarm status for each dry contact alarm.  Red indicates that the dry contact alarm is
active and light blue indicates the alarm is inactive.  If the Remote Power Switch function is enabled, then the AAI
Alarm  In  status  will  not  be  present  from  the  AAI  alarm  status  since  this  function  is  disabled  when  the  Remote
Power Switch is enabled.

Figure 7-3

Status Tab – AAI Alarm Display (Remote Power Switch Disabled)

Figure 7-4

Status Tab – AAI Alarm Display (Remote Power Switch Enabled)

«
...
36
37
38
39
40
...
»

Summary of Contents for PSR-78-9533-UA





























































Reviews:

No comments

Related manuals for PSR-78-9533-UA

Brand: Ultimate Sound Pages: 7

Brand: Atlona Pages: 10

Brand: Clockaudio Pages: 3

Brand: Triode Lab Pages: 9

Brand: Teac Pages: 96

Brand: NJS Pages: 8

Brand: Idea Pages: 6

Brand: Analog Devices Pages: 20

Brand: NAD Pages: 2

Brand: Genie Pages: 5

Brand: Cable-Tronix Pages: 5

Brand: Cobalt Digital Inc Pages: 36

Brand: Klipsch Pages: 10

Brand: Kicker Pages: 20

400M Neo Series

Brand: moon Pages: 14

Brand: JET CITY AMPLIFICATION Pages: 12

Brand: C2G Pages: 19

Brand: Teac Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands