ADRF PSR-78-9533-UA Manual Download

Page: 25 / 60

Advanced RF Technologies, Inc.

4.2 External Alarms

The PSR-78-9533-UA supports dry contact alarms and can be connected to a fire alarm control panel. The user can program
the repeater to either create an open or closed circuit when an alarm is present in the system.

4.2.1

External Alarm Output interface

Simplex Alarm Box

Simplex

Digital Board

24V dc

ADRF PSR Repeater

ADRF

Digital Board

Table 4-2

External Alarm

External Alarm Name

Set Condition

Likely Causes

Donor Antenna Malfunction

UL Return Power Hard Fail

Damaged Donor Antenna

Active RF Device Malfunction

RF Power Soft Fail

DL Return Power Hard Fail

DL/UL Over Power Hard Fail

DL/UL Input Overload Hard Fail

Degrading Amplifier

Open or Disconnected Server Port

Oscillation

Strong RF Input Signal

Low Battery Capacity (70% depleted)

Low Battery Soft Fail

Battery Depleted

System Component Malfunction

Over Current Hard Fail

Over Temperature Hard Fail

DSP Hard Fail

Out-band Overload Hard Fail

Faulty or Damaged PSU

Ambient Temperature

DSP Filter Fault

Strong RF Input Signal

Normal AC Power

AC Normal Set

AC Fail Soft Clear

Loss of Normal AC Power

AC Fail Soft Set

AC Normal Clear

Battery Charger Failure

Battery Fail Soft Fail

Battery Not Connected Soft fail

Battery Not Charge Soft Fail

Low Battery Charging Voltage

Battery Cable Disconnected

Degraded Batteries

Summary Alarm

Any Active Alarm

Any Active Alarm Present in the System

Donor Antenna Disconnect

No DL Signal Detected

Disconnected Donor Line

Oscillation Alarm

Oscillation Hard Fail

Gain Set Too High or Lack of Isolation

Annunciator Disconnect

Annunciator Disconnect Hard Fail

Disconnected PSR-ANN

Summary of Contents for PSR-78-9533-UA





























































Search results

Summary of Contents for PSR-78-9533-UA

Reviews:

Related manuals for PSR-78-9533-UA

Brands by name

Popular brands

ADRF PSR-78-9533-UA, Manual

Search results

Summary of Contents for PSR-78-9533-UA

Reviews:

Related manuals for PSR-78-9533-UA

Brands by name

Popular brands