ADMtek ADM5120 Datasheet Download Page 55

Page: 55 / 112

ADM5120

4.4.8 Mem_control, offset: 0x1c

Bits

Type Name

Description

Initial value

2:0

SDRAMsize

one bank information, the 2

bank (SDRAM_CS1) is

the same
000, 101, 110, 111: reserved,
001: 1Mx32 (4Mbyte),
010: 2Mx32 (8Mbyte) (suggested setting)
011: 4Mx32 (16Mbyte),
100: 16Mx32 (64Mbyte)
101: 32Mx32 (128Mbyte)

4:3

Reserved

Not

Applicable

SDRAM1_en

The bank1 of SDRAM enable,
0: disable (default),
1: enable (must in the single write)

7:6

Reserved

Not

Applicable

10:8 RW

SRAM0_size

000: disable if in the NAND mode,
110, 111: reserved,
001: 512Kbyte,
010: 1Mbyte (default)
011: 2Mbyte,
100: 4Mbyte

010

15:11

Reserved

Not

Applicable

18:16 RW

SRAM1_size

000: disable (default),
001: 512Kbyte,
010: 1Mbyte
011: 2Mbyte,
100: 4Mbyte,
101: 8Mbyte,
110, 111: reserved

000

28:19

Reserved

Applicable

29 RW

CSX0_wt_hold_ext

Extend the write data hold time from one clock to 3
clock (clock period = CLK_OUT) 0: normal, 1 clock,
default, 1: extend to 3 clocks

31:30

Reserved

Not Applicable

4.4.9 SW_conf, offset: 0x20

ADMtek Inc.

4-8

Bits

Type Name

Description

Initial value

0 Reserved

Not

Applicable

3:1

Reserved

Not

Applicable

7:4 RW age_tmr

aging

timer

→

0000: disable age, 1xxx: fast age

0001: 300sec,
0010: 600 ……
0111: 38400sec

0001

9:8 RW BC_prev

Broadcast

prevention:

Summary of Contents for ADM5120

















































































































Search results

Summary of Contents for ADM5120

Reviews:

ADMtek ADM5120, Datasheet, Page: 55 / 112

Search results

Summary of Contents for ADM5120

Reviews: