ADLINK Technology Q7-AL, User Manual

Page: 41 / 95

Q7-AL
Connector Pinouts on Module
31
Table 2: 36-pin MIPI-CSI Camera Connector Pin Definition on the Qseven Module
Pin Signal Description
1 V3P3S 3.3 volts +/-5% to power the camera device (output)
2 V3P3S 3.3 volts +/-5% to power the camera device (output)
3 MCSI1_D0_P CSI1 Camera 0 Data Lane 0+
4 MCSI1_D0_N CSI1 Camera 0 Data Lane 0-
5 GND Ground
6 MCSI1_D1_P CSI1 Camera 0 Data Lane 1+
7 MCSI1_D1_N CSI1 Camera 0 Data Lane 1-
8 GND Ground
9 MCSI1_D2_P CSI1 Camera 0 Data Lane 2+
10 MCSI1_D2_N CSI1 Camera 0 Data Lane 2-
11 MCSI1_CAM0RST# Camera 0 Reset (active low; CMOS 1.8V; output)
12 MCSI1_D3_P CSI1 Camera 0 Data Lane 3+
13 MCSI1_D3_N CSI1 Camera 0 Data Lane 3-
14 GND Ground
15 MCSI1_CLK_P CSI1 Camera 0 Differential Clock+ (Strobe; PHY; input)
16 MCSI1_CLK_N CSI1 Camera 0 Differential Clock- (Strobe; PHY; input)
17 GND Ground
18 CN_I2C_CAM0_CK Camera 0 Control Interface Clock (I2C-like interface; CMOS 1.8V OD; output)
19 CN_I2C_CAM0_DAT Camera 0 Control Interface Data (I2C-like interface; CMOS 1.8V OD; input/output)
20 CAM0_ENA# Camera 0 Enable (active low; CMOS 1.8V; output)
21 CAM_MCLK_R Master Clock (may be used by cameras to drive internal PLL; frequency range: 6-
27MHz; CMOS 1.8V; output)
22 CAM1_ENA# Camera1 Enable (active low; CMOS 1.8V; output)
23 CN_I2C_CAM1_CK Camera 1 Control Interface Clock (I2C-like interface; CMOS 1.8V OD; output)
24 CN_I2C_CAM1_DAT Camera 1 Control Interface Data (I2C-like interface; CMOS 1.8V OD; input/output)
25 GND Ground
26 MCSI2_CLK_P CSI2 Camera 1 Differential Clock+ (Strobe; PHY; input)
27 MCSI2_CLK_N CSI2 Camera 1 Differential Clock- (Strobe; PHY; input)
28 GND Ground
29 MCSI2_D0_P CSI2 Camera 1 Data Lane 0+ (D-PHY; input)
30 MCSI2_D0_N CSI2 Camera 1 Data Lane 0- (D-PHY; input)
31 MCSI_CAM1RST# Camera 1 Reset (active low; CMOS 1.8V; output)
32 MCSI2_D1_P CSI2 Camera 1 Data Lane 1+ (D-PHY; input)
33 MCSI2_D1_N CSI2 Camera 1 Data Lane 1- (D-PHY; input)
34 GND Ground
35 CAM0_GPIO GPIO for Camera 0 (CMOS 1.8V; input/output)
36 CAM1_GPIO GPIO for Camera 1 (CMOS 1.8V; input/output)