background image

BIOS Setup 

 45

PXIe-3985

Table  B-3: BIOS Advanced Setup Menu

B.4 Boot Setup

Table  B-4: BIOS Boot Setup Menu

B.5 Security Setup

The system can be configured to require all users to enter a pass-
word (either Administrator or User) every time the system boots or
when Setup is executed. Administrators and User passwords acti-
vate different levels of security.

Serial Port 
Configuration

Set COM port mode between RS232/422/485

Miscellaneous

Includes precision timer and security setting

Item

Detail

Boot Configuration

Quiet Boot

When disabled, allows POST messages to be 
viewed (default is Enabled).

Bootup NumLock 
State

Selects default keyboard number lock setting

CSM16 Module 
Version

Displays the version of the CSM16 module, e.g. 
07.64

Gate A20 Active

Allows GA20 to be disabled by BIOS

Option ROM 
Messages

Sets display mode for Option ROM

Interrupt 19 Capture

Allows Option ROMs to trap Int 19

Set Boot Priority

1st Boot

Allows selection of the primary boot source (default 

is the SATA HDD)

2nd Boot

Allows selection of the secondary boot source 

(default is Disabled)

Hard Drive BBS 
Priorities

Sets the order of legacy devices in this group

Item

Detail

Summary of Contents for PXIe-3985































































Reviews: