ADLINK Technology PXI-2020 User Manual Download Page 32 | Manualshive

Page: 32 / 60

ADLINK Technology PXI-2020 User Manual Download Page 32

24

Function Block and Operation Theory

4.2

Basic AI Acquisition

In this section, the basic acquisition timing is explained.

4.2.1

Analog Input Path

The following figure shows the block diagram of the single analog
input path of a PXI-2020/2022. Each path provides a choice of 1G

Ω

input impedance or high impedance. The gain amplifier is opti-

mized for ±10 V and ±2.5 V input range with low noise and high
dynamic range. An anti-aliasing filter is also adopted to eliminate
high frequency noise. The 16-bit ADC provides not only accurate
DC performance but also high signal-to-noise ratio, high spurious-
free dynamic range in AC performance.

Figure 4-2: PXI-2020/2022 Analog Input Path

4.2.2

Basic Acquisition Timing

The trigger is a signal that starts or stops the acquisition. In post-
trigger mode and delay trigger mode, the trigger is used to initiate
acquisition. In pre-trigger mode, the trigger is used to stop acquisi-
tion. In middle-trigger mode, the trigger is used to inform the acqui-
sition engine to acquire the specific number of data and then stop.

Timebase is a clock that sent to the ADC of each channel and the
acquisition engine for essential timing functionality. The source of
timebase can be either internal oscillator or external clock genera-
tor. Usually the maximum sampling rate of a Data Acquisition
Module is determined by the speed of timebase. However, other
sampling rate can be achieved by specifying a scan interval coun-

An ti -al iasi ng

Fil ter

Calibration S ource +

P rot ect ion

Ci rcuitry

Gain = 1 or 4

16-bit

250 KS ADC

Onboard
Me mo ry

P CI Interface

Hi I mpedance

B uff er

Calibrat ion S ource -

AI+

A I-

«
...
30
31
32
33
34
...
»

Summary of Contents for PXI-2020





























































Reviews:

No comments