ADLINK Technology DMI-1210 User Manual Download

Page: 99 / 103

DMI-1210

6.7

Boot Menu

This menu contains the settings for bootable devices in the sys-
tem.

BIOS Item

Options

Description

Setup Prompt

Timeout

Number of seconds to wait for setup

activation key. 65535 (0xFFFF)

means indefinite waiting.

Bootup NumLock

State

Off

Select the keyboard NumLock state

after system boot.

Quiet Boot

Disabled

Enabled

Enabled:

will show splash screen

during POST.

Disabled:

will show boot message

during POST.

Fast Boot

Disabled

Enabled

Enable or disabled Fast boot feature.

Most probes are skipped to reduce

time cost during boot.

Boot mode select

LEGACY

UEFI

Select boot mode, LEGACY/UEFI.

Boot Option #1~#8 Hard Disk

CD/DVD
USB Hard Disk
USB CD/DVD
USB Key
USB Floppy
USB Lan
Network
Disabled

Set system boot order.

Summary of Contents for DMI-1210








































































































Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands

ADLINK Technology DMI-1210, User Manual

Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands