ADLINK Technology DMI-1210 User Manual Download

Page: 88 / 103

Leading

EDGE COMPUTING

6.5.3

Uncore Configuration

Enables/disables Integrated Graphic Device and RC6 (Render-

Standb), sets size for GTT, aperture size, DVMT pre-alloca-
tion,DVMT total Gfx Mem and CD clock frequency.

BIOS Item

Options

Description

Integerated

Graphics Devices

Disable

Enable

Enable: Enable Integrated Graphics

Device (IGD) when selected as the

Primary Video Adaptor.
Disable: Always disable IGD.

Primary Display

IGD

PCIe
HG

Select which of IGD / PCI Graphics

device should be Primary Display.

Aperture Size

128MB

256MB

512MB

Select the Aperture Size.

DVMT Pre-

Allocated

64M

96M
128M
160M
192M
224M
256M
288M
320M
352M
384M
416M
448M
480M
512M

Select DVMT 5.0 Pre-Allocated

(Fixed) Graphics Memory size used

by the Internal Graphics Device

DVMT Total Gfx

Mem

128M

256M

MAX

Select DVMT5.0 Total Graphic

Memory size used by the Internal

Graphics Device

Summary of Contents for DMI-1210








































































































Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands

ADLINK Technology DMI-1210, User Manual

Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands