ADLINK Technology DMI-1210 User Manual Download

Page: 86 / 103

Leading

EDGE COMPUTING

6.4.14

Intel I210 Gigabit Network Connection

NIC Configuration

Device power-up

delay

Auto

Manual

Maximum time the device will take

before properly reporting itself
to the Hot Controller, with ‘Auto’

using default value, for a Root
port 100 ms, and for a Hub port the

delay is taken from the Hub
descriptor.

BIOS Item

Options

Description

NIC Configuration

Submenu

For configuring link speed and wake

function.

Blink LEDs

Value Range

Identifies the physical network port

by blinking the associated
LED.

BIOS Item

Options

Description

Link Speed

Auto Negotiated

10 Mbps Half
10 Mbps Full
100 Mbps Half
100 Mbps Full

For setting link speed of Ethernet.

Wake On LAN

Enabled

Disabled

For enabling/disabling wake on LAN

function.

BIOS Item

Options

Description

Summary of Contents for DMI-1210








































































































Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands

ADLINK Technology DMI-1210, User Manual

Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands