ADLINK Technology DMI-1210 User Manual Download

Page: 73 / 103

DMI-1210

6.3.4

Board Information

BIOS Item

Options

Description

Serial Number

Info only

Display board’s serial number.

Manufacturing Date

Info only

Display manufacturing date.

Last Repair Date

Info only

Display Last Repair Date.

MAC ID

Info only

Display onboard Ethernet MAC ID.

Total Runtime

Info only

The returned value specifies the total

time in minutes the system is running

in S0 state.

Current Runtime

Info only

The returned value specifies the time

in seconds the system is running in

S0 state.
This counter is cleared when the

system is removed from the external

power supply.

Power Cycle

Info only

The returned value specifies the

number of times the external power

supply has been shut down.

Boot Cycles

Info only

The boot cycle is increased after a

HW or SW reset or after a successful

power-up.

Boot Reason

Info only

The boot reason is the event which

causes the reboot of the system.

Summary of Contents for DMI-1210








































































































Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands

ADLINK Technology DMI-1210, User Manual

Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands