ADLINK Technology cPCI-7300A User Manual Download Page 69 | Manualshive

Page: 69 / 114

background image

Operation Theory

59

4.11.4 Pattern Generator

The digital data is output to the peripheral device periodically
based on the clock signals occur at a constant rate. The digital
pattern are stored in the cPCI/PCI/PCIe-7300A’s on-board FIFO
with the length of pattern less than or equal to 16K samples.

The operations sequence of pattern generator are listed:

1. Define the input configuration to be 32-bit, 16-bit or 8-bit

data width.

2. Enable or disable the active terminators.

3. Define the output timer pacer rate to be 20MHz, 10MHz,

or the output 82C54 timer 1. The timer pacer controls the
output rate.

4. Set the output patterns into the output FIFO by direct

FIFO access

5. Start the pattern generator function.

6. The pattern generator function will not stop until users

stop the process

«
...
67
68
69
70
71
...
»

Summary of Contents for cPCI-7300A



















































































































Reviews:

No comments

Related manuals for cPCI-7300A

C50FSi - VB Network Camera

Brand: Canon Pages: 32

Brand: Rabbit Pages: 120

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: T&D Pages: 122

Brand: Opengear Pages: 2

IMACS Network Device

Brand: Zhone Pages: 114

Brand: Xantech Pages: 4

Brand: Compro Technology Pages: 2

Brand: VideoWave Pages: 12

Brand: 2N Telekomunikace Pages: 67

Brand: Neousys Technology Pages: 24

COM Express conga-TC87

Brand: Congatec Pages: 114

Brand: Telit Wireless Solutions Pages: 79

Brand: Fibocom Pages: 39

Brand: Radionics Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands