manualshive.com logo in svg

ADLINK Technology aTCA-3710, User Manual

Share
Download
ADLINK Technology aTCA-3710 User Manual Download Page 22

                                                 aTCA-3710 User's Guide

 

 
 

 22 

   

Figure 7. Broadcom SDK Function Blocks 

 

The ADLINK Software for Network (ADSN) is based on the Broadcom SDK and includes all Layer 2 and 
Layer 3 switching functions. 

The Fabric & Base Switches (BCM56842/56846/56334) can also be paired with ADSN. ADSN includes 
functions of port configuration, customized port mirror, VLAN setting, trunk group, ACL, static route, and 
management API with a more user-friendly CLI to enable more straightforward API development. 

The details of the ADSN release software can be found in the 

ADSN Configuration Guide 

and 

ADSN 

API Programming Guide

. 

They will not be covered in this document.   

Under default settings, the system will boot to the Broadcom BCM SDK shell. Please contact your 
ADLINK representative to order ADLINK Software for Network. 

Summary of Contents for aTCA-3710






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands