GB
GB
BEFORE USE
HANDLING OF THE PACKED MACHINE
The machine is supplied with suitable packing fore-
seen for fork lift truck handling.
The total weight is 95 kg.
Packing dimensions:
Base:
118 cm x 67 cm
Height:
119 cm
ATTENTION:
Do not place more than 2 packings on top of each
other.
UNPACKING OF THE MACHINE
1. Remove the external packing.
2. Unscrew the brackets (1+2) that secure the ma-
chine to the pallet.
3. Move the machine backwards, as indicated in
figure, avoiding heavy contacts to mechanical parts.
4. Keep the pallet for eventual transport.
BATTERY INSTALLATION AND SETTING OF THE
BATTERY TYPE
This machine is equipped with two batteries at 12V
in serial connection, placed in its appropriate com-
partment under the recovery tank and must be han-
dled using suitable lifting equipment (due to weight
and coupling system).
The batteries must be in accordance with CEI 21-5
Norms.
The connection of the batteries' cables has to be car-
ried out by specialized staff, because the inversion of
polarity causes the damage of the electrical compo-
nents. Before the machine is supplied with power,
check that the red cable is connected to the + pole
of the battery.
For batteries installation proceed as follows:
1. Take off the squeegee hose (1).
2. Take off the suction cover (2) after turning the
blocking levers (3).
3. Take off the recovery tank (4).
4. Place the batteries in its compartment.
5.
Connect the terminals, respecting the polari-
ties, avoiding contact with other parts that could
create short circuit.
6. Reassemble all parts.
ATTENTION:
The machine and the signal lamp of the battery
charge level foresee the use of traditional lead bat-
teries.
In case of GEL batteries installation, it is necessary to
carry out a specific adjustment. Please contact the
authorized technical assistance.
ATTENTION:
Strictly follow manufacturer/distributor indications
for the maintenance and daily recharge of the bat-
teries. All installation and maintenance operations
must be executed by specialized staff, using suitable
protection accessories.
BATTERY RECHARGER
Be sure that the battery recharger is suitable for
the installed batteries both for their capacities
and type (lead/acid or GEL and equivalent).
In the plastic bag containing the use and mainte-
nance you will find the coupling connector for the
recharger. It must be assembled onto the cables of
your recharger, following the instructions given by
the manufacturer.
ATTENTION:
This operation must be carried out by qualified staff.
A wrong or faulty cable connection can create seri-
ous damages to persons or things.
BATTERIES RECHARGING
Bring the machine on a levelled surface.
Plug in batteries connector (1) placed in the rear
part of the machine, to connector (2) of the battery
recharger.
ATTENTION:
Never charge a GEL battery with a non suitable
recharger. Strictly follow the instructions sup-
plied by the batteries and recharger manufactur-
er.
In order not to cause permanent damages to the
batteries, it is necessary to avoid their complete dis-
charge, providing for the recharging within a few
minutes after batteries discharge signal starts blink-
ing.
NOTE: Never leave batteries completely discharged
even if the machine is not used. In case of traditional
batteries, please check the electrolyte level every 20
recharging cycles and eventually fill them up with
distilled water after having carried out a complete
recharge.
ATTENTION:
For the daily recharge of the batteries it is necessary
to follow strictly all the indications given by the
manufacturer/distributor. All the installation and
maintenance operations must be carried out by
qualified staff.
Danger of gas exhalations and
emission of corrosive liquids. Fire danger: do not
approach with free flames.
BATTERIES DISPOSAL
It is compulsory to hand over exhaust batteries, clas-
sified as dangerous waste, to an authorized institu-
tion according to the current laws.
BATTERIES CHARGE LEVEL INDICATOR
Activating the push button of the brushes (2) the
signal lamp of the battery charge level (1) will come
on.
When the signal lamp is in
green colour
it means
that the battery charge level is
sufficient
for the
functioning of the machine.
If the signal lamp is in
red colour
it means that the
battery charge level is
insufficient
for the function-
ing of the machine and it is necessary to recharge
immediately the batteries (see under "BATTERIES RE-
CHARGING”).
17
Summary of Contents for ruby 45 light
Page 2: ......
