ADDER AdderLink XDIP User Manual Download Page 20 | Manualshive

Page: 20 / 63

ADDER AdderLink XDIP User Manual Download Page 20

19

CONFIGURA

TION

RESTORING A NODE

In order to obtain the full benefit of the configuration wizard when creating a new
installation, it may be necessary to restore the default settings to your XDIP nodes.

Note: A restore operation will reset all configuration settings and cannot be undone.

A restore operation can be invoked in various ways:

•

[Receivers]

Display the channel list and then click the icon in the top right corner. If

requested, enter the admin password and then choose the

Software Upgrade

page.

Click the

Restore

button:

ADMIN - Software Settings and Upgrade

Receiver 1

Software Settings and Upgrade

General

Bootloader

Recovery

Active

Alternate

v1.00 - 18:15 30/07/17

v1.00 - 18:15 30/07/17

v1.00.0066 - 13:37 30/07/17

v1.0021 - 18:15 19/06/17

Select Upgrade File

Switch to Alternative Version

Restore Default Settings

Reboot Node

OSD Settings

Setup Channels

Manage Ports

Advanced

Software Upgrade

RECEIVER

Review the software versions present on this node. Upgrade, switch to the alternative software
version, restore or reboot this node.

Select File

Upgrade

Switch

Restore

Reboot

RECOVERY - Software Settings and Upgrade

Review the software versions present on this node. Upgrade,
switch to the alternative software version, restore or reboot this
node.

Bootloader:

Recovery:

Preferred:

Alternate:

v1.00 - 18:15 30/07/17

v1.00 - 18:15 30/07/17

v1.00 - 18:15 30/07/17

v1.00 - 18:15 30/07/17

Select Upgrade File

Switch to Alternative Version

Restore Default Settings

Reboot Node

Select File

Upgrade

Switch

Restore

Reboot

•

[Receivers or transmitters]

Use a narrow implement

(such as a straightened out paper clip) to press and
hold the recessed reset button on the front panel
(while power is applied) for just over ten seconds

until the front panel PWR indicator flashes; then

release the button and wait for the node to
reboot and display the Recovery page. Click the

Restore

button.

Notes:

•

The reset button is within the hole to the left of the

USB socket.

•

You will need a minimum of a monitor and either

keyboard/mouse connected to the node being

restored.

•

[Transmitters]

From any connected receiver node, display the channel list and then click

the

icon in the top right corner. If requested, enter the admin password and then

choose the Setup Channels page.

•

Click the

icon shown next to the name of the transmitter that you wish to restore,

then choose the

Software Upgrade

page and click the

Restore

button:

ADMIN - Software Settings and Upgrade

Transmitter 2

General

Manage Ports

Advanced

Software Upgrade

TRANSMITTER

Review the software versions present on this node. Upgrade, switch to the alternative software
version, restore or reboot this node.

Software Settings and Upgrade

Bootloader

Recovery

Active

Alternate

v1.00 - 18:15 30/07/17

v1.00 - 18:15 30/07/17

v1.00.0066 - 13:37 30/07/17

v1.0021 - 18:15 19/06/17

Select Upgrade File

Switch to Alternative Version

Restore Default Settings

Reboot Node

Upgrade

Switch

Restore

Reboot

Select File

«
...
18
19
20
21
22
...
»

Summary of Contents for AdderLink XDIP
































































Reviews:

No comments